Skip to main content
HVAC Service

Heat Pump Repair & Service in North Central Florida

Is your system constantly stuck in expensive auxiliary heat mode? We diagnose the underlying mechanical failure and restore reliable warmth to your home.

Scott Niehaus AC repairs heat pumps for homeowners in Alachua and Gilchrist counties. The $125 diagnostic trip fee is applied to the repair. Call (352) 332-9247; after hours, the line reaches an on-call technician or emergency voicemail.

Who repairs heat pumps in North Central Florida?

Scott Niehaus Air Conditioning & Heating repairs heat pumps across North Central Florida, isolating the exact component failure in the defrost controls or refrigerant cycle before the compressor suffers permanent damage.

Is your outdoor unit trapped inside a solid block of ice, are your vents blowing cold air when you set the thermostat to heat, or is the system constantly stuck in auxiliary mode? These are serious mechanical failures within your defrost controls or refrigerant cycle that demand professional diagnostics before the compressor suffers permanent damage. Scott Niehaus Air Conditioning & Heating is ready to isolate the exact component failure and get your system operating smoothly again.

What are the warning signs your heat pump needs repair?

Warning signs your heat pump needs repair include auxiliary heat that stays on, an outdoor unit encased in ice, vents blowing cold air in heat mode, grinding, squealing, or gurgling noises, and short cycling.

The Auxiliary Heat Stays On

Your thermostat constantly displays the auxiliary or emergency heat setting even when outdoor temperatures are relatively mild, which causes your electric bill to skyrocket. This indicates your primary heat pump cycle has failed, forcing the system to rely entirely on the expensive electric resistance backup strips located in your air handler to warm your home. Ignoring this issue masks a serious mechanical problem with the outdoor unit and will eventually burn out those backup strips entirely, leaving you with absolutely no heat.

The Outdoor Unit is Encased in Ice

While a light, temporary layer of frost is a normal part of the heating cycle, an outdoor unit trapped inside a solid block of ice means the automatic defrost cycle has completely failed. If the system continues to run while frozen solid, the expanding ice will crush the delicate aluminum coil fins, and the fan blades can shatter against the ice buildup. This requires immediate attention to manually thaw the unit safely and replace the faulty defrost controls before the compressor overheats and suffers irreversible damage.

Vents Blowing Cold Air in Heat Mode

You set the thermostat to heat, but the air coming out of your bedroom vents feels exactly like the air conditioning is running full blast. This is the classic symptom of a stuck reversing valve, which is the internal brass component responsible for physically shifting the flow of high-pressure refrigerant between cooling and heating modes. The system will run continuously without ever reaching your set temperature, putting heavy, unnecessary wear on the blower motor and compressor while leaving your home completely uncomfortable.

Loud Grinding, Squealing, or Gurgling Noises

The outdoor unit sounds like metal grinding on metal, emits a high-pitched squeal, or makes a distinct bubbling sound through the copper refrigerant lines running into your house. Grinding and squealing usually point to failing bearings in the condenser fan motor, while gurgling indicates low refrigerant levels from an active leak in the closed loop. These strange noises are the final warning before a critical component seizes completely, meaning you need to shut the system down immediately to prevent an expensive compressor replacement.

Short Cycling On and Off

Your heat pump turns on, runs for only a few minutes, and then shuts off abruptly before your home actually reaches the desired temperature on the thermostat. This rapid cycling puts immense electrical and mechanical stress on the compressor and is often caused by a failing run capacitor, a severely clogged air filter, or an improper refrigerant charge triggering the low-pressure switch. A technician needs to evaluate the system pressures and electrical draw to stop the cycle before the compressor burns out from the constant starting torque.

What causes heat pump failures?

Common causes of heat pump failures include a stuck or failing reversing valve, broken defrost controls, refrigerant leaks in the coils, and fried capacitors and contactors.

A Stuck or Failing Reversing Valve

Because heat pumps in North Central Florida run in cooling mode for most of the year, the reversing valve can easily stick when you finally switch it over to heat. We start by testing the electrical solenoid coil to see if it is receiving the proper low voltage from the control board, and if the coil has failed, we can replace it quickly on the spot. If the mechanical valve itself is jammed internally, the repair is much more intensive; we must safely recover the existing refrigerant, cut out the old valve, flow nitrogen while brazing in a new one, pull a deep vacuum, and recharge the system.

Broken Defrost Controls

High humidity combined with sudden temperature drops creates heavy frost buildup on outdoor coils, forcing the defrost cycle to work overtime to keep the unit clear. Over the years, the electronic defrost control board or the temperature sensors degrade and fail to trigger the necessary melting process by temporarily switching the unit back into cooling mode. We test the defrost thermostat and control board to isolate the exact electrical failure, swap out the faulty part, and manually trigger a test cycle to verify the repair is successful.

Refrigerant Leaks in the Coils

Vibration, corrosion, and weak factory brazing can cause microscopic holes in the indoor evaporator coil or the outdoor condenser coil, allowing your refrigerant to slowly escape. Because heat pumps require an exact refrigerant charge to heat your home efficiently without damaging the compressor, we use highly sensitive electronic leak detectors to pinpoint the precise location of the leak. Depending on the severity, we then repair the copper line or replace the leaking coil entirely, test the system with pressurized nitrogen, and recharge the refrigerant to factory specifications.

Fried Capacitors and Contactors

Heat pumps run year-round in our climate, meaning their electrical components take far more abuse than a standard air conditioning system that gets the winter off. The dual-run capacitor that jump-starts the motors and the contactor switch that pulls in the high voltage to turn the unit on eventually succumb to heat, power surges, and general mechanical wear. We safely discharge the electrical system, remove the bulging or burned component, and wire in a high-quality replacement to get the motors firing properly without straining the compressor.

What happens during a heat pump repair visit?

A heat pump repair visit starts at the thermostat, moves to refrigerant pressure and electrical tests at the outdoor unit, and ends with a plain-English explanation of the problem and what it will cost.

When you call Scott Niehaus Air Conditioning & Heating, you get a licensed, EPA-certified technician who understands the specific demands placed on heat pumps in North Central Florida. We start our diagnostic process at the thermostat to verify how the system is communicating, checking the low voltage wiring to ensure the call for heat is actually reaching the equipment. From there, we head to the outdoor unit to hook up our manifold gauges, check the internal refrigerant pressures, and measure the subcooling and superheat to see exactly how the system is performing under a load. We test the reversing valve solenoid, measure the electrical amp draw on the compressor, and manually trigger the defrost cycle to see exactly where the failure is occurring.

Once we pinpoint the exact mechanical or electrical problem, we sit down with you and explain the issue in plain English without hiding behind confusing industry jargon. We provide a blunt, honest assessment of what it will take to fix the system, exactly how much it will cost, and whether the repair makes long-term financial sense for your home based on the age and condition of the equipment. Failed relays, capacitors, sensors, and contactors are common heat pump repairs, and the $125 diagnostic fee applies to the repair.

Heat Pump Repair & Service Coverage Across North Central Florida

Communities We Serve: Gainesville, FL, Newberry, FL, Alachua, FL, High Springs, FL, Archer, FL, Jonesville, FL, Waldo, FL, Hague, FL, Trenton, FL, Worthington Springs, FL, Williston, FL

What other heat pump services are available?

Related services include heat pump installation and replacement for systems too old to repair, and routine heat pump maintenance and tune-up visits to catch failing electrical parts early.

Sometimes a heat pump is simply too old, or the compressor has failed entirely, making a massive repair cost-prohibitive. In those situations, we will walk you through your options for a full heat pump installation and replacement so you can upgrade to a more reliable, energy-efficient system. To keep your current or new equipment from breaking down when you need it most, we also highly recommend scheduling routine heat pump maintenance and tune-up visits to catch failing electrical parts early.

Get Your Heat Pump Running Right Again

Let our owner-operated team diagnose the real mechanical issue and restore your home's comfort. Reach out to Scott Niehaus Air Conditioning & Heating to schedule your heat pump repair today.

Flat diagnostic fee, flat repair pricing
EPA 608 certified technicians, FL License CAC057109
After-hours emergency line
1-year parts & labor warranty on new installs

Request Service

Tell us what's going on

Free estimates on system replacements. Repairs start with a $125 diagnostic.

Contact Us

Loading form. If it does not load, please use the other contact options on this page.

By submitting, you agree to our Privacy Policy and Terms.

Prefer to talk?

Mon–Fri 8–5. After hours, our on-call tech or emergency voicemail.

(352) 332-9247